LATE MODEL PARTS AND TOOLS UPDATE

  Deal of the DAY, don't want to drag this chassis to Harrisburg on Fri,
 2001 BRC LAZER 2 Chassis, bare frame with inner sheetmetal $200 OR BEST OFFER,
 2- BRC 20390 LAZER TOP 4-LINK 1 1/2" ALUM SHOCK MOUNT $25 EA,
 2- UNIVERSAL 1 1/2" STEEL SHOCK MOUNTS $10 EA,
 ALUM FRAME BRACKET WITH AJUSTABLE TAPPED HOLES FOR PANHARD OR J-BAR $75,
 1- AJUSTABLE PANHARD/J-BAR $25,
 PANHARD/J-BAR SINGLE PINION MOUNT $15,
 SQUARE 2X2 PANHARD/J-BAR FRAME MOUNT DOUBLE-SIDE $10,
 PAIR LEFT AND RIGHT LAZER 2 FRONT SPINDLES $75,
 1- 10" SPLIT UPPER CONTROL ARM $20,
 1- 8" UPPER CONTOL ARM $15,
 1- UPPER PRECISION REPAIRABLE BALL JOINT $25,
 1-LOWER PRCISION REPAIRABLE SCREW-IN BALL JOINT $25
 USED UPPER REG BALL JOINTS $10 EA,
 CRAFTSMAN 15 PC SOCKET SET 3/8" TO 1 1/8" $50,
 3 PC FILE SET $15
 3 PC PRY-BAR SET $15,
 NEW STARTER & SWITCH PIGTAIL PLUG $10,
 1- STEEL CHEVY-BERT TRANS COULPER $10,
 2- 5 gal fuel jugs $10 ea,
 SHUT OFF AND FUEL FILTER WITH STAINLESS FILTER ELEMENT $30,
 1- FILTER ALUM BRACKET 1 1/2" TUBE $8,
 2 GAUGE PANEL OIL PRESSURE/WATER TEMP $20,
 2- new 8"X 72" lexan spoilers $40 ea,
 Alum stagger gauge  $25,
 QA1 9500 made into a dumming shock $2
 1- 36" axle $25,
 1- 34" axle $25,
 2- Bicknell brake calipers --.38 rotor $50 ea,
 Pittsburgh 1/2" SAE deep impact socket set in case 7/16" to 1 1/4" $25,
 1/2" drive short impact sockets loose 3/8" to 15/16" no 7/16 socket $15,
 3 pc speedway pry bar set (screwdriver type) $10,
 Wright 1/2"SAE 1" deep socket $3
 1/2" SAE torque wrench $20,
 Lug wrench 1" socket welded on $15,
 Central Pneumatic 3" air high speed cut off tool $25,
 10 pack 3" cut off metal blades $6,
 350 chevy 2 bolt main with stock cast iron crankshaft $50,
 NEW 1205 fel-pro intake gasket $15,
 3- HP4 fram racing oil filters $21,
 K&N spray air filter oil $7 ea,
 85- short steel dzus buttons $60,
 17- long steel dzus buttons $14,
 50 pack old steel dzus buttons $10,(have lots more, let me know what you need
 open trailer with tire rack $700,
 engine hoist $125,
 parts washer $50,
 Electronic specialties model ES-130 battery timing light $80
 STEEL SEALED bearing BIRD CAGES LEFT AND RIGHT $175,
 2- DRIVE FLANGES $10 EA,
 FLUSH MOUNT REAR FILL TANK $15,
 REAR  HAND PUMP FOR 5 GAL BUCKET $20,
 Winters 4.86 quick-change rear axles were 34" and 36" $450,
 Right side winters side bell 4 web $25,
 2- side bell axle seals $3 ea,
 right sibe 6 wed with large fill plug $25,
 1- 2 piece alum 14-5 non bead $25,
 1- new wilwood dynalite .81 brake caliper $80,
 1- used wilwood dynalite .81 caliper $40,
 QA-1 coil-over kits $10 ea,
 PRO 90/10 SHOCK $20,
 1- AFCO TAKE-UP SPRING $5,
 3- NEW AFCO NYLON SLIDER FOR TAKE-UP SPRING $8 EA,
 Gears-
 winters:
 8510- 6.58 $25,
 set 1429 FRP 21/30 teeth $10,
 sixth coil with spring $60,
 used radiator chevy $75,
 power steering pump $35,
 power steering reservoir $15,
 double brake pedals, rev swing, with master cylinders $150,
 CAT LJ water pump SBC with by-pass outlets $40,
 32 gal LM alky fuel cell in a can- $50,
 250 Watt tire groover $25,
 new heims--QA1 Precision products rod-ends-- kevar race,self lubrcating teflon liner:
 2- XMR10 5/8 x 5/8 heims RH $18 ea,
 2- XML10 5/8 x 5/8 heims LH $18 ea,
 2- XMR8 1/2 x 5/8 heims RH $18 ea,
 used LM fiberglass roof, with carbon fiber cap- black 45 x 48- $50,
 Alum seat with pads $75,
 2.5lb fire bottle $50,
 LM shifters $15,
 LM header with mufflers $50,
 stock alum bell housing $15,
 2- LIGHT WEIGHT LM drive shaft 39 1/2" long with 4 3/4" slip yoke $50,
 slip yoke 3 3/4" with joints $20,
 2- Barrel pumps $15 ea,